Quantcast EXPLANATION OF COLUMNS IN THE MAC, SECTION II.

 

Click here to make tpub.com your Home Page

Page Title: EXPLANATION OF COLUMNS IN THE MAC, SECTION II.
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Remove/Install.
Up
TM-32-5865-061-24-P Receiver Set R-2197/MLQ-34 Part Number 5051640-1NSN
Next
EXPLANATION OF COLUMNS IN REMARKS, SECTION IV.
TM 32-5865-061-24&P
B-3 .
EXPLANATION OF COLUMNS IN THE MAC, SECTION II.
a . C o l u m n 1 , G r o u p N u m b e r .  C o l u m n 1 lists functional group code numbers, the
purpose of which is to identify maintenance significant components, assemblies,
s u b a s s e m b l i e s , and modules with the next higher assembly. End item group number
shall be "00".
b .  Column 2, Component/Assembly.  C o l u m n 2 contains the names of components,
assemblies, subassemblies, and modules for which maintenance is authorized.
C o l u m n 3, Maintenance Function. Column 3 lists the functions t o be
(For  detailed  explanation of these
p e r f o r m e d on the item listed in column 2.
functions, see paragraph B-2.)
Column 4 specifies, by the listing of a work
d .  C o l u m n 4, Maintenance Level.
time figure in the appropriate sub-column(s), the category of maintenance autho-
rized to perform the function listed in column 3. This figure represents the
active time required to perform that maintenance function at the indicated
category of maintenance.
If the number or complexity of the tasks within the
listed maintenance function vary at different maintenance categories, appropriate
work time figures will be shown for each category. The work time figure re-
presents the average time required to restore an item (assembly, subassembly
component, module, end item, or system) to a serviceable condition under typical
field  operating  conditions.  This time includes preparation time (including any
necessary disassembly/assembly time), troubleshooting/fault location time, and
quality assurance/quality control time in addition to the time required to perform
the specific tasks identified for the maintenance functions authorized in the
m a i n t e n a n c e  a l l o c a t i o n  c h a r t .  T h e symbol designations for the various maintenance
levels are as follows:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . O p e r a t o r or crew
C
.
O
.
......
. . . . . .  .  .  .  .  . . . . .  Organizational  maintenance
F
. . . . . . . . . . . . . . . . . . . . . . . . . . . . D i r e c t support maintenance
.
H
.
. . . . . . . . . . . . . . . ... . ....... . G e n e r a l support maintenance
D
. . . D e p o t maintenance
.
........... ..................
e .  C o l u m n 5, Tools and Equipment.
C o l u m n 5 s p e c i f i e s , by code, those common
tool sets (not individual tools) and special tools, TMDE, and support equipment
required to perform the designated function.
f .  C o l u m n 6. Remarks.
This column shall, when applicable, contain a letter
c o d e , in alphabetic order, which shall be keyed to the remarks contained in
Section IV.
EXPLANATION OF COLUMNS IN TOOL AND TEST EQUIPMENT REQUIREMENTS,
B-4 .
SECTION III.
Reference Code.  T h e tool and test equipment reference code
a .  Column 1.
c o r r e l a t e s with a code used in the MAC, Section II, Column 5.
b .  Column 2.  M a i n t e n a n c e L e v e l .
T h e lowest level of maintenance authorized
t o use t h e t o o l o r t e s t e q u i p m e n t .
B-3

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc.
6230 Stone Rd, Unit Q Port Richey, FL 34668

Phone For Parts Inquiries: (727) 493-0744
Google +