Quantcast RF Cable Assemblies (W1 thru W33), R e m o v a l / I n s t a l l a t i o n - continued - TM-32-5865-061-24-P0051

 

Click here to make tpub.com your Home Page

Page Title: RF Cable Assemblies (W1 thru W33), R e m o v a l / I n s t a l l a t i o n - continued
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
TABLE 5-4. RF CABLE ROUTING - continued
Up
TM-32-5865-061-24-P Receiver Set R-2197/MLQ-34 Part Number 5051640-1NSN
Next
RF Cable Assemblies (W1 thru W33), R e m o v a l / I n s t a l l a t i o n - continued - TM-32-5865-061-24-P0052
TM 32-5865-061-24&P
(7) Raise and secure the heat-sink panel.
(8) Install A10, refer to para 5-4.3.
d.
R e m o v e cable assemblies W17 thru W20 as follows:
( 1 ) D i s c o n n e c t t h e S M A c o n n e c t o r a t t h e P 1 e n d o f t h e cable (AT1 thru
AT4). .
CAUTION
W h e n unfastening cable ties, take care not to cut or damage wiring in
t h e harness.
(2) Unfasten the cable-ties securing the cable to the harness. Loosen
c a b l e clamps as necessary.
( 3 ) Loosen the two screws to release the c a b l e - c l a m p a t t h e r e a r o f t h e
c o n n e c t o r at the E1 end of the cable (XA1P2 thru XA4P2).
(4) Using extraction tool CET-6B (access from front of unit), remove the
coaxial contact from the connector.
(5) Remove the cable from the unit.
(6) To install a replacement cable, reverse the procedure described i n
s t e p s d . ( 1 ) t h r u d . ( 5 ) .  T o r q u e SMA connector to 8 inch-pounds.
(7) Raise and secure the heat-sink panel.
(8) Install A10, refer to para 5-4.3.
e . Remove cable assemblies W25 thru W28 as follows:
( 1 ) Remove the jam-nut securing the connector at the P1 end of the cable
to the rear panel (J13 thru J16).
CAUTION
W h e n unfastening cable ties, take care not to cut or damage wiring in
t h e harness.
(2) Unfasten the cable ties securing the cable to the harness. Loosen
c a b l e clamps as necessary.
( 3 ) D i s c o n n e c t t h e S M A c o n n e c t o r a t t h e P 2 e n d o f the cable (AR1 OUTPUT
thru AR4 OUTPUT).
(4) Remove the cable assembly from the unit.
(5) To install
a replacement cable, reverse the procedure described in
s t e p s e . ( 1 ) t h r u e . ( 4 ) .  T o r q u e SMA connectors to 8 inch-pounds.
(6) Raise and secure the heat-sink panel.
5-19

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc.
6230 Stone Rd, Unit Q Port Richey, FL 34668

Phone For Parts Inquiries: (727) 493-0744
Google +