TM 11-5895-687-34 P-4
quantity of the item used in the breakout shown
on the illustration figure, which is prepared for a
complete repair of the support item is the
functional group, subfunctional group, or an
depot level, performed by depot.
ZNonreparable. No repair is authorized.
(3) Recoverability code. Recoverability codes
4. Special Information
are assigned to support items to indicate the
a. The following publications pertain to the
disposition action on unserviceable items. The
RT-903/TPX-50 and its components:
recoverability code is entered in the fifth position
TM 11-5895-687-12, Interrogator Set
of the Uniform SMR Code format as follows:
T M 11-5895-687-35-4. Interrogator Set
A N / T P X - 5 0 (Receiver-Transmitter,
ZNonreparable item. When serviceable, condemn
and dispose at the level indicated in
T M 11-5895-687-20P, Interrogator Set
F Reparable item. W h e n uneconomically
b. National stock numbers (NSN's) that are
reparable, condemn and dispose of at the
missing from P source-coded items have been
direct Support level.
applied for and will be added to this manual by
D Reparable item. When beyond lower level
future change/revision when they are entered in
repair capability, return to depot. Con-
the Army Master Data File (AMDF). Until the
demnation and disposal not authorized
NSN's are established and published, submit
below depot level.
exception requisitions to: Commander, US Army
LReparable item. Repair, condemnation, and
Electronics Command, ATTN: DRSEL-MN, Fort
Monmouth, NJ 07703 for the part required to
depot/specialized repair activity level.
support your equipment.
c. National Stock Number. Indicates the
5. How to Locate Repair Parts
National stock number assigned to the item and
a. When National stock number or part number
will be used for requisitioning purposes.
d. Part Number. Indicates the primary number
(1) First. Using the table of contents,
used by the manufacturer (individual, company,
determine the functional group or subgroup within
firm, corporation, or Government activity), which
which the repair part belongs. This is necessary
controls the design and characteristics of the item
since illustrations are prepared for functional
by means of its engineering drawings, specification
groups or subgroups, and listings are divided into
standards, and inspection requirements, to identify
the same groups.
an item or range of items.
(2) Second. Find the illustration covering
functional group or subgroup to which the repair
W h e n a stock-numbered
requisitioned, the repair part received may
(3) Third. Identify the repair part on the
have a different part number than the part
illustration and note the illustration figure and
item number of the repair part.
e. Federal Supply Code for Manufacturer
(4) Fourth. Using the Repair Parts Listing,
(FSCM). The FSCM is a 5-digit numeric code
find the figure and item number noted on the
listed in SB 708-42 which is used to identify the
manufacturer, distributor, or Government a g e n c y ,
b. When National stock number or part number
f. Description. Indicates the Federal item name
(1) First. Using the Index of National Stock
and, if required, a minimum description to identify
Numbers and Part Numbers, find the pertinent
National stock number or part number. This index
g. Unit of Measure (U/M). Indicates the
is in aecending NSN sequence, followed by a list
standard of the basic quantity of the listed item as
of part numbers in ascending alphameric sequence,
used in performing the actual maintenance func-
cross-referenced to the illustration figure number
tion. This measure is expressed by a two-
and item number.
character alphabetical abbreviation (e.g., ea, in,
(2) Second. After finding the figure and item
pr, etc). When the unit of measure differs from
number, locate the figure and item number in the
the unit of issue, the lowest unit of issue that will
repair parts list.
satisfy the required units of measure will be
h. Quantity Incorporated in Unit. Indicates the
(Next printed page is 4.1.)