Quantcast Figure FO-17. Clarifier Control Fault Isolation Flow Chart 5865-01-076-9050">

 

Click here to make tpub.com your Home Page

Page Title: Figure FO-17. Clarifier Control Fault Isolation Flow Chart
Back | Up

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Figure FO-16. MAC Control Fault Isolation Flow Chart
Up
TM-11-5865-215-13 Receiver Control C-10026/USQ NSN
TM 11-5865-215-13
q
WITH OSCILLOSCOPE
REPLACE
CHECK FOR PULSE
CCA Al
ACTIVITY ATA3-105
I
CHANNEL A
1. CONNECT CHANNEL D OF OSCILLOSCOPE TO A3-106
I
(0671). THIS NEGATIVE GATE ESTABLISHES THE TEST
I
INTERVAL WITHIN WHICH ALL DATA IS MEASURED
(REFER TO FIGURE A). ADJUST OSCILLOSCOPE SWEEP
I
SO THAT THE GATE FILLS THE WIDTH OF THE TRACE.
INTERNALLY SYNC THE OSCILLOSCOPE TO THE
I
NEGATIVE EDGE OF THIS GATE.
(1623)
2. CONNECT OSCILLOSCOPE CHANNEL B TO
CHANNEL B
AND CHANNEL C TO A3-1OO (1622).
3. ROTATE CLARIFIER CONTROL FULL CW. OBSERVE BOTH
CHANNELS C AND B OF THE OSCILLOSCOPE ARE HIGH
V).
(APPROX
ROTATE THE CLARIFIER CONTROL CW WHILE
4.
1. WITH A VOLTMETER CHECK A3-68
CHANNEL C
OBSERVING CHANNELS C AND B:
AND A3
(-).
a. CHANNEL C SHOULD SHOW 32 HIGH-TO-LOW
2. WHEN THE CLARIFIER CONTROL IS
TRANSITIONS.
FULL CCW THE VOLTMETER SHOULD
b. CHANNEL B SHOULD SHOW 16 HIGH-TO-LOW
THIS VOLTAGE DECREASES
READ
I
--
TRANSITIONS.
TO OV AS THE CONTROL IS ROTATED
TO THE FULL CW POSITION.
5. WHEN THE CLARIFIER CONTROL IS FULLY CW BOTH
INTERVAL
CHANNELS C AND B SHOULD BE LOW.
q
I
FIGURE A
REMOVE AND
REPLACE CCAS
CHANGE THE CHANNEL D PROBE TO
(0670).
Al AND A5
7. CONNECT THE CHANNEL A PROBE TO A3-101 (1621).
8. ROTATE THE CLARIFIER CONTROL FULL CCW. OBSERVE CHANNELS A, B, AND C ARE HIGH.
ROTATE THE CLARIFIER CONTROL
OBSERVE THE OSCILLOSCOPE:
9.
4 HIGH-TO-LOW TRANSITIONS
a. CHANNEL A SHOULD
b. CHANNEL B SHOULD SHOW 1 HIGH-TO-LOW TRANSITION
TRANSITIONS
c. CHANNEL C SHOULD SHOW 2 HIGH -TO-
10. WHEN THE CLARIFIER CONTROL IS FULL CW CHANNELS A, B, AND C SHOULD BE LOW.
REPLACE
11. CHANGE THE CHANNEL C PROBE TO A3-102
NO
REPLACE
CLARIFIER
12. ROTATE THE CLARIFIER CONTROL FULL CCW, OBSERVING CHANNEL C GOES HIGH.
CCA A3
CONTROL
OBSERVING CHANNEL C CHANGES HIGH-TO-LOW 8 TIMES.
13. ROTATE THE CLARIFIER CONTROL
CHANNEL C SHOULD BE LOW.
14. WHEN THE CLARIFIER CONTROL IS FULL
\
EL3RJ062
Clarifier Control
Fault Isolation Flow Chart

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc.
6230 Stone Rd, Unit Q Port Richey, FL 34668

Phone For Parts Inquiries: (727) 493-0744
Google +